Multi-Tech Systems MT5634SMI Manual de usuario Pagina 86
- Pagina / 136
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 3 – Fax Class 2 Commands
Multi-Tech Systems, Inc. SocketModem MT5634SMIxx Reference Guide (S000263C) 86
T.30 Session Error Report, +FAXERR
Class 2.0/2.1 not supported
Class 2 +FAXERR
Read syntax: > +FAXERR= <table value>, read only
Valid values: 0–255; see Table 3.5 for meaning
This read only parameter indicates the cause of a hang-up. Table 3.5 shows the valid
values for this parameter as well as the meaning of each value. +FAXERR is set by
the modem at the conclusion of a fax session. The modem will reset this to 0 at the
beginning of Phase A off-hook time.
Minimum Phase C Speed, +FMS
Class 2.0/2.1 +FMS
Write syntax: +FMS=BR
Valid values: 0–5, in BR subparameter codes
Default value: 0 (V.27ter @ 2400 bit/s)
This optional parameter limits the lowest negotiable speed for a session. It is useful
for limiting the cost of a transmission by requiring a minimum transmission speed. If a
facsimile cannot negotiate to a minimum speed, it performs an orderly disconnect.
The units are the same as those defined for the BR Bit Rate subparameter as defined
in Table 3.6 in this manual.
Class 2 +FMINSP
Write syntax: +FMINSP=BR
Valid values: 0–5, in BR subparameter codes
Default value: 0 (V.27ter @ 2400 bit/s)
This optional parameter limits the lowest negotiable speed for a session. It is useful
for limiting the cost of a transmission by requiring a minimum transmission speed. If a
facsimile cannot negotiate to a minimum speed, it performs an orderly disconnect.
The units are the same as those defined for the BR Bit Rate subparameter, as
defined in Table 3.6 in this manual.
- SocketModem™ 1
- SocketModem Reference Guide 2
- Contents 3
- Chapter 1 – AT Commands, S 5
- Registers and Result Codes 5
- AT Command Summary 6
- Command Description 7
- AT Commands 8
- Escape AT Commands 21
- V.92 Commands 22
- S-Registers 28
- Result Codes 31
- 32 32
- Commands 33
- Fax Mode Selection 34
- Fax Origination 34
- Fax Answering 34
- Fax Control Transmission 34
- Fax Control Reception 35
- Fax Data Transmission 36
- Fax Data Reception 36
- Commands and Parameters 37
- Service Class 1 Commands 41
- Command: +FLO Flow Control 44
- Examples 45
- 47 47
- AT Command Implementation 49
- Modes of Interaction 50
- Command Execution Mode 52
- Data Transfer Mode 52
- Action Commands 55
- Modem Responses 56
- 57 57
- 58 58
- Identification Commands 59
- Service Class Selection 60
- Request Model Identification 60
- Data Transmission 62
- Post-Page Message Release 62
- Data Reception 63
- Session Termination 63
- Class 2.1 +FPO 65
- Class 2 +FPOLL 65
- Class 2.1 +FPS: 68
- Class 2 +FPTS: 68
- Class 2.1 +FET: 69
- Class 2 +FET: 69
- Class 2.1 +FHS: 69
- Class 2 +FHNG: 69
- 71 71
- Parameter Commands 72
- Class 2.1 +FIS= 73
- Class 2 +FDIS= 73
- Class 2.1 +FCS? 73
- Class 2 +FDCS? 73
- 75 75
- 76 76
- Class 2.1 +FLI 77
- Class 2 +FLID 77
- Class 2.1 +FPI 77
- Class 2 +FCIG 77
- Class 2.1 +FNS 78
- Class 2.1 +FLP 78
- Class 2 +FLPL 78
- Class 2.1 +FSP 78
- Class 2 +FSPL 78
- Class 2.1 +FCR 79
- Class 2 +FCR 79
- Class 2.1 +FBU 79
- Class 2 +FBUG 79
- Class 2.1 +FNR 80
- Class 2.1 +FAP 80
- Class 2.1 +FSA, +FPA, +FPW 81
- Class 2.1 +FPS 82
- Class 2 +FPTS 82
- Class 2 +FCQ 83
- Class 2.1 +FCQ 83
- Class 2.1 +FRQ 84
- Class 2 +FBADMUL 84
- Class 2 +FBADLIN 84
- Class 2.1 +FAA 85
- Class 2 +FAA 85
- Class 2 85
- Class 2.0/2.1 not supported 86
- Class 2 +FAXERR 86
- Class 2.0/2.1 +FMS 86
- Class 2 +FMINSP 86
- Class 2.0/2.1 +FBO 87
- Class 2 +FBOR 87
- Class 2.0/2.1 +FEA 87
- Class 2 +FREL 87
- Class 2.0/2.1 88
- Fax Flow Control, +FLO 90
- Miscellaneous Parameters 92
- +FDCS:<dcs codes> 95
- CONNECT 95
- <page data stream> 95
- 800 bit/s ability 98
- 400 bit/s is 98
- 600 bit/s 99
- 800 bit/s is 99
- Responses 100
- 101 101
- ASCII Conversion Chart 102
- Chapter 4 – Voice Commands 103
- Voice S-Register Summary 104
- Voice Commands 104
- Support 104
- Voice +V Commands Detail 105
- Voice +V Commands Summary 105
- (20-100) , (150-180) , (200 119
- Flow Control 121
- Voice Mode Result Codes 121
- Voice Mode Shielded Codes 123
- Sample Sessions 125
- DTE/DCE Interface Rates 128
- Remote Configuration 129
- Country Code Configuration 130
- 131 131
- 132 132
- 133 133
- 134 134
- 135 135
- 136 136
© 2020, manymanuals.es. Todos los derechos reservados | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales