Multi-Tech Systems MT5634SMI Manual de usuario Pagina 19
- Pagina / 136
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 1 – AT Commands, S-Registers and Result Codes
Multi-Tech Systems, Inc. SocketModem MT5634SMIxx Reference Guide (S000263C) 19
Command: #CBAn Callback Attempts
Values: n = 1–255
Default: 4
Description: Sets the number of callback attempts that are allowed after passwords have
been exchanged between modems.
Command: #CBDn Callback Delay
Values: n = 0–255
Default: 15
Description: Sets the length of time (in seconds) that the modem waits before calling back
the remote modem.
Command: #CBF? Callback Failed Attempts Display
Values: N/A
Default: N/A
Description: Requests the number of failed callback passwords since reset or power-up.
This number can be stored to nonvolatile memory using the &W command.
Command: #CBFR Callback Failed Attempts Reset
Values: N/A
Default: N/A
Description: Resets the number of failed callback passwords to 0. This does not reset the
number stored in nonvolatile memory.
Command: #CBIn Local Callback Inactivity Timer
Values: n = 1–255
Default: 20
Description: Sets the time (in minutes) that the modem waits for a command before
forcing the user to enter the setup password again.
Command: #CBNy=x Store Callback Password
Values: y = 0–29
x = password
Defaults: None
Description: Sets the callback security password for the y memory location. The password
must have 6 to 10 characters, and cannot include the + or - characters.
Command: #CBPn Callback Parity
Values: n = 0, 1, or 2
Default: 0
Description: Sets parity for the callback security messages.
#CBP0 No parity.
#CBP1 Odd parity.
#CBP2 Even parity.
- SocketModem™ 1
- SocketModem Reference Guide 2
- Contents 3
- Chapter 1 – AT Commands, S 5
- Registers and Result Codes 5
- AT Command Summary 6
- Command Description 7
- AT Commands 8
- Escape AT Commands 21
- V.92 Commands 22
- S-Registers 28
- Result Codes 31
- 32 32
- Commands 33
- Fax Mode Selection 34
- Fax Origination 34
- Fax Answering 34
- Fax Control Transmission 34
- Fax Control Reception 35
- Fax Data Transmission 36
- Fax Data Reception 36
- Commands and Parameters 37
- Service Class 1 Commands 41
- Command: +FLO Flow Control 44
- Examples 45
- 47 47
- AT Command Implementation 49
- Modes of Interaction 50
- Command Execution Mode 52
- Data Transfer Mode 52
- Action Commands 55
- Modem Responses 56
- 57 57
- 58 58
- Identification Commands 59
- Service Class Selection 60
- Request Model Identification 60
- Data Transmission 62
- Post-Page Message Release 62
- Data Reception 63
- Session Termination 63
- Class 2.1 +FPO 65
- Class 2 +FPOLL 65
- Class 2.1 +FPS: 68
- Class 2 +FPTS: 68
- Class 2.1 +FET: 69
- Class 2 +FET: 69
- Class 2.1 +FHS: 69
- Class 2 +FHNG: 69
- 71 71
- Parameter Commands 72
- Class 2.1 +FIS= 73
- Class 2 +FDIS= 73
- Class 2.1 +FCS? 73
- Class 2 +FDCS? 73
- 75 75
- 76 76
- Class 2.1 +FLI 77
- Class 2 +FLID 77
- Class 2.1 +FPI 77
- Class 2 +FCIG 77
- Class 2.1 +FNS 78
- Class 2.1 +FLP 78
- Class 2 +FLPL 78
- Class 2.1 +FSP 78
- Class 2 +FSPL 78
- Class 2.1 +FCR 79
- Class 2 +FCR 79
- Class 2.1 +FBU 79
- Class 2 +FBUG 79
- Class 2.1 +FNR 80
- Class 2.1 +FAP 80
- Class 2.1 +FSA, +FPA, +FPW 81
- Class 2.1 +FPS 82
- Class 2 +FPTS 82
- Class 2 +FCQ 83
- Class 2.1 +FCQ 83
- Class 2.1 +FRQ 84
- Class 2 +FBADMUL 84
- Class 2 +FBADLIN 84
- Class 2.1 +FAA 85
- Class 2 +FAA 85
- Class 2 85
- Class 2.0/2.1 not supported 86
- Class 2 +FAXERR 86
- Class 2.0/2.1 +FMS 86
- Class 2 +FMINSP 86
- Class 2.0/2.1 +FBO 87
- Class 2 +FBOR 87
- Class 2.0/2.1 +FEA 87
- Class 2 +FREL 87
- Class 2.0/2.1 88
- Fax Flow Control, +FLO 90
- Miscellaneous Parameters 92
- +FDCS:<dcs codes> 95
- CONNECT 95
- <page data stream> 95
- 800 bit/s ability 98
- 400 bit/s is 98
- 600 bit/s 99
- 800 bit/s is 99
- Responses 100
- 101 101
- ASCII Conversion Chart 102
- Chapter 4 – Voice Commands 103
- Voice S-Register Summary 104
- Voice Commands 104
- Support 104
- Voice +V Commands Detail 105
- Voice +V Commands Summary 105
- (20-100) , (150-180) , (200 119
- Flow Control 121
- Voice Mode Result Codes 121
- Voice Mode Shielded Codes 123
- Sample Sessions 125
- DTE/DCE Interface Rates 128
- Remote Configuration 129
- Country Code Configuration 130
- 131 131
- 132 132
- 133 133
- 134 134
- 135 135
- 136 136
© 2020, manymanuals.es. Todos los derechos reservados | 0.187 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales