Multi-tech-systems BA-Series Manual de usuario Pagina 67
- Pagina / 109
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
67
Chapter 7 - DIP-Switch Settings
Switch #2
SDLC/BSC Option
(Synchronous Mode/Leased Line/Dial-Up)
Synchronous Data Link Control (
SDLC
) and Binary Synchronous Control (
BSC
) are two error
correction protocols used in the IBM Mainframe environment. Place DIP-Switch #2 in the UP position
to enable SDLC mode, and place DIP-Switch #2 in the DOWN position to enable BSC mode.
SDLC Mode = Switch #2 UP
BSC Mode = Switch #2 DOWN
Factory Default Setting = UP
Switch #3
Enable/Suppress Responses -- "Q"
(Asynchronous Mode/Dial-Up)
In some Asynchronous mode applications, you may want to suppress all responses from the modem.
Place DIP-Switch #3 in the DOWN position to enable Result Code responses (
Q0
). Place DIP-Switch
#3 in the UP position, and answer mode is handled without responses and echo turned off (
Q2
), but
originate is still intelligent.
Enable Responses: Originate/Answer (
Q0
) = Switch #3 DOWN
Suppress Responses: Answer (
Q2
) = Switch #3 UP
Factory Default Setting = DOWN
Switch #3
dB Transmission Levels
(Asynchronous/Synchronous Mode/Leased Line)
DIP-Switch #3 adjusts dB transmission levels required by some phone carriers. Place DIP-Switch #3
in the DOWN position to enable -9 dB transmission. Place DIP-Switch #3 in the UP position to enable
-15 dB transmission.
-9dB Transmission = Switch #3 DOWN
-15dB Transmission = Switch #3 UP
Factory Default Setting = DOWN
Switch #4
AS/400 Mode
(Synchronous Mode/Leased Line/Dial-UP)
The modem can function in the IBM AS/400 environment (appearing like an IBM5853 modem). First,
DIP-Switch #7 must be placed in the UP position. This establishes an RTS/CTS condition (state
typical for an IBM5853 modem in half-duplex mode). Next, place DIP-Switch #4 in the DOWN
position. This
"spoofs"
the modem into operating like an IBM5853 modem in AS/400 applications.
DIP-Switch #4 in the UP position disables this function. Note that the modem must be in Command
mode to allow AS/400 mode (DIP-Switch #8 DOWN); and in Synchronous mode (DIP-Switch #12
UP).
AS/400 Mode Enabled = Switch #4 DOWN
AS/400 Mode Disabled = Switch #4 UP
Factory Default Setting = UP
- BA-Series 1
- Intelligent Data/Fax Modem 1
- User Guide 1
- Contents 3
- 1.1 Introduction 6
- 1.2 How To Use This Manual 6
- 1.3 Modem Features 7
- 1.3.1 2834 Series Features 8
- 1.4 Fax Features 8
- 1.5 Technical Specifications 9
- 1.6 Power 10
- 1.7 Modem LED Indicators 11
- 1.8 Controls on PC Board 12
- 2.2 Installation 14
- 2.2.1 Safety Warnings 15
- 2.2.2 Installation Procedure 15
- EIA RS232C 16
- 3.1 Introduction 18
- 3.2 Configuring Your Software 18
- 3.4 PC Initialization Strings 18
- 3.4.2 Other Parameters 19
- 3.5.2 Terminal Emulation 20
- 3.5.3 File Transfer Protocols 20
- Chapter 4 - Command Mode 21
- 4.1 Introduction 22
- 4.1.1 AT Command Editing 22
- 4.1.2 Functional Modes 22
- 4.2 Summary of AT Commands 23
- 4.3 Result Codes 26
- 4.4 Dialing Commands 27
- 4.4.1 Dialing Action Commands 27
- 4.4.2 Dial Modifier Commands 28
- 1028806127853500$123456789 30
- Number Linking NN 31
- Modem Reset Z 32
- Unix UUCP Spoofing $SP 32
- Bell/V.21 Tone B 35
- Auto Speed Detect #A 36
- Carrier Detect Control &C 36
- CTS Control &R 37
- Data Set Ready Control &S 37
- Normal Mode &E0 38
- Auto-Reliable Mode &E1 38
- Reliable Mode &E2 38
- V.42 Mode Select #L 38
- Auto-Reliable Buffering $A 39
- 4.4.9 Flow Control Commands 40
- Hardware Flow Control &E4 41
- Xon/Xoff Flow Control &E5 41
- Xon/Xoff Pass-Through &E7 41
- Send Xon/Xoff Characters #X 42
- Maximum Block Size &BS 42
- Through and Pacing Commands 43
- Speed Conversion $BA 44
- Modem Baud Rate $MB 44
- Serial Port Baud Rate $SB 45
- Off Hook H 47
- BREAK AT<CR> 47
- Force Answer Mode A 47
- 4.4.13 Line Probe Commands 48
- Chapter 5 - S-Registers 49
- 5.1 Introduction 50
- &S 53
- (2834 Series only) 55
- Remote Configuration 57
- 6.1 Introduction 58
- Configuration 58
- Change LOGIN Password #I 62
- Local Inactivity Timer (S29) 64
- 7.1 Introduction 66
- "UUCP spoofing" 68
- 7.3 Speaker Volume Control 71
- DIP-Switches 72
- DIP Switches #13-14 73
- DIP Switches #15-16 73
- 8.1 Introduction 75
- 8.4 Replacement Parts 77
- 8.5 Technical Support 77
- 8.6 Internet Sites 77
- Appendixes 78
- Upgrade Overview 79
- Programming Complete 81
- Appendix B - Troubleshooting 82
- I Am Losing Data 85
- Password Command Summary 94
- V.25bis Commands 95
- Delayed and Forbidden Numbers 96
- V.25bis Operation 96
- V.25bis Mode AT Commands 97
- V.25bis AT Commands 98
- DTR Dialing ($D) Command 100
- NO CARRIER 101
- 25-PIN DTE 102
- Connector 102
- 25-PIN DCE 102
- FCC Part 15 103
- FCC Part 68 Telecom 103
- Canadian Limitations Notice 104
Relacionado con productos y manuales para Hardware Multi-tech-systems BA-Series
Hardware Multi-tech-systems MR9600 Manual de usuario
(86 paginas)
(86 paginas)
Hardware Multi-tech-systems 7500 Manual de usuario
(372 paginas)
(372 paginas)
Hardware Multi-tech-systems ISIHP-2U Manual de usuario
(155 paginas)
(155 paginas)
Hardware Multi-tech-systems MT5634MSV Manual de usuario
(114 paginas)
(114 paginas)
Hardware Multi-tech-systems RF802EW Manual de usuario
(118 paginas)
(118 paginas)
Hardware Multi-tech-systems ISI3334/4 Manual de usuario
(232 paginas)
(232 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.076 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales