Multi-tech-systems DataTalker DT101/xx Manual de usuario Pagina 42
- Pagina / 154
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
42
DataTalker Owner’s Manual
3.4.3 DIP Switch
The eight-position DIP switch is accessible through a cutout in the left side of the DataTalker
series enclosure; its location is shown in Figures 3-3 and 3-4.
Position 1: Not used
Position 2: OPEN (up) Internal composite link device selected
Closed (down) External composite link device selected
Position 3: OPEN (up) Data channel selected
Closed (down) Command channel selected
Position 4: Not used
Position 5: OPEN (up) MMV8/16/32 mode—for communicating with an
MMV800-, MMV1600-, or MMV3200-series mux
Closed (down) 101 mode—for communicating with an MMV101
or a DataTalker
Position 6: Not used
Position 7: Not used
Position 8: Not used
3.4.4 RS232C/V.35 Shunt
You can connect an external composite link device using either an RS232/V.24 or a V.35
interface to the DataTalker’s External Composite connector. To configure the DataTalker for V.35
operation you must move a shunt on the main circuit board. Two shunt sockets are located on
the back left side of the board (Figures 3-3 and 3-4). When an external composite link device with
an RS232C/V.24 interface is connected to the composite link, the shunt is installed in the RS232
socket (factory default). When the external composite link device has a V.35 interface, you must
move the shunt from the default RS232 socket to the V.35 socket. The V.35 indicator on the front
panel lights when the shunt is in the V.35 position.
- Data/Voice/Fax Concentrator 1
- Owner’s Manual 1
- 82052704 Revision E 2
- DataTalker™ Series 2
- Contents 3
- Chapter 5 - Installation 4
- Chapter 6 - Menus 4
- Chapter 7 - Troubleshooting 4
- 1.1 Introduction 8
- 1.2 About This Manual 8
- 1.3 Product Description 10
- 1.4 System Features 12
- 1.4.6 Diagnostics 13
- 1.4.7 Operational Statistics 13
- 1.7 Specifications 16
- 1.7.5 Internal Modem 17
- 1.7.6 Internal DSU 17
- 1.7.7 ISDN Terminal Adapter 17
- 1.7.8 Voice/Fax Channel 17
- 1.7.9 Electrical/Physical 18
- Chapter 2 - Configuration 19
- 2.1 Introduction 20
- Home Office 21
- 101 MDM/TA 25
- Composite Link 28
- Local Site 32
- Remote Site 32
- 3.1 Introduction 36
- 3.2 Indicators 36
- 3.3 Connectors 39
- 3.3.9 MODEM LEASED Connector 40
- 3.4 Switches and Shunts 41
- 3.4.3 DIP Switch 42
- 3.4.4 RS232C/V.35 Shunt 42
- 4.1 Introduction 44
- 4.2 Unpacking 44
- 4.3 Configuration Summary 45
- 4.7 Configuration Procedure 48
- Data Port Async/Sync 50
- 1 - Async 50
- 2 - Sync 50
- P - Previous Menu 50
- Selection : _ 50
- 5.1 Introduction 56
- 5.2 Cabling 56
- RJ-48 Cable 57
- Internal DSU/TA 57
- DIGITAL Connector 57
- To External 58
- Composite 58
- Link Cable 58
- RJ-11 Phone Cable 59
- VOICE/FAX 59
- CHANNEL 1 59
- FXO Connector 59
- 5.3 V.35 Shunt 60
- 5.4 Power-On and Checkout 61
- 6.1 Introduction 66
- 6.2 Configurations Menu 66
- 6.2.1 Data Port Configuration 67
- DataTalker 71
- P - Previous Menu 74
- 6.3 Statistics 78
- 6.4 Reset Options 79
- 6.5 Diagnostic Tests 79
- 6.5.1 Loop Tests 80
- 6.6 Configure Remote Unit 81
- 6.6.2 Quick Setup 82
- RJ11 Phone 83
- DATA/COMMAND 84
- Connector 84
- RS232 Cable 84
- 7.1 Introduction 88
- 7.3 Test Cables 89
- 7.4 Troubleshooting Guide 90
- Internal MMH2834 Modem 94
- Async Data Channel 96
- Sync Data Channel 96
- 7.9 Composite Link Statistics 103
- 7.10Data Port Configuration 105
- 7.12Diagnostic Testing 109
- DataTalker Owner’s Manual 110
- 8.1 Introduction 112
- 8.2 Limited Warranty 112
- 8.3 Tech Support 113
- 8.4 The Multi-Tech BBS 114
- 8.5 About the Internet 115
- Appendixes 117
- Appendix C - Cabling Diagrams 120
- Composite Link Cabling 121
- Voice/Fax Channel Connectors 123
- DSU Back-to-Back Cable 123
- DATA DATA 124
- F.1 Introduction 127
- F.2 Dialing Action Commands 129
- F.3 Dial Modifier Commands 130
- Wait for New Dialtone W 131
- Flash On Hook ! 131
- “Calling Card” Detect Tones $ 131
- Quiet Answer @ 131
- Storing Phone Numbers D...N 132
- Number Linking N...N 132
- Modem Reset Z 133
- F.9 Error Correction Commands 138
- Retransmit Count $R 139
- Data Compression 140
- Maximum Block Size &BS 140
- Speed Conversion $BA 141
- Modem Baud Rate $MB 141
- Serial Port Baud Rate $SB 142
- F.12Immediate Action Commands 143
- Glossary 145
Relacionado con productos y manuales para Faxes Multi-tech-systems DataTalker DT101/xx
Faxes Multi-tech-systems MT5634ZBAV Manual de usuario
(170 paginas)
(170 paginas)
Faxes Multi-tech-systems E1 Manual de usuario
(395 paginas)
(395 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.108 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales