Multi-tech-systems MMCModem GPRS (MTMMC-G) Manual de usuario Pagina 114
- Pagina / 203
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 13 – Specific AT Commands
Multi-Tech Systems, Inc. Wireless GSM/GPRS AT Commands (Document Number S000293I) 114
Read GPIO Value +WIOR
Description: Read the requested GPI or GPIO pin value.
Notes:
• By default (e.g., after a reset), the I/O ports configuration is set by the +WIOM command.
• This command is allowed only on a GPIO not allocated by an Open-AT embedded application or
for bus operations.
• When the BT chip is switched on, the GPIO5 is not available anymore.
Values: <index>
Up to ten I/O ports are available. The <index> value is between 0 and 9.
<value>
0 I/O port number <index> is reset.
1 I/O port number <index> is set.
Syntax: Command syntax: AT+WIOR=<index>
Response syntax: +WIOR: <value>
Command Possible responses
AT+WIOR=0
Read I/O (number 0) value
+WIOR: 0
OK
GPIO number 0 is reset
Write GPIO Value +WIOW
Description: Set the requested GPO or GPIO pin value.
Notes:
• By default (e.g., after a reset), the I/O ports configuration is set by the +WIOM command.
• This command is allowed only on a GPIO not allocated by an Open-AT embedded application or
for bus operations.
• When the BT chip is switched on, the GPIO5 is not available anymore. It is not possible to
change the state of the GPIO using this command.
Values: <index>
Up to ten I/O ports are available. The <index> value is between 0 and 9.
<value>
0 I/O port number <index> is reset.
1 I/O port number <index> is set.
Syntax: Command syntax: AT+WIOW=<index >,<value>
Command Possible responses
AT+WIOW=2,0
Reset I/O (number 2)
OK
GPIO value is written
- Wireless GSM/GPRS Modems 1
- Contents 3
- Chapter 1 – Introduction 9
- Chapter 2 – AT Command 10
- Features 10
- Background Initialization 11
- Chapter 4 – General AT 13
- Request IMSI +CIMI 15
- Card Identification +CCID 15
- Capabilities List +GCAP 15
- Repeat Last Command A/ 15
- Power Off +CPOF 16
- Keypad Control +CKPD 17
- Clock Management +CCLK 18
- Alarm Management +CALA 18
- Chapter 5 – Call Control 19
- Hang-Up Command H 20
- Answer a Call A 21
- Remote Disconnection 21
- DTMF Signals +VTD, +VTS 21
- Automatic Answer S0 23
- Incoming Call Bearer +CICB 24
- Gain Control +VGR, +VGT 24
- Echo Cancellation +ECHO 27
- Chapter 6 – Network Service 31
- Network Registration +CREG 33
- Read Operator Name +WOPN 34
- Read Operator Name +COPN 39
- Chapter 7 – Security 40
- Enter PIN2 +CPIN2 42
- Facility Lock +CLCK 43
- Change Password +CPWD 44
- Chapter 8 – Phonebook 45
- Subscriber Number +CNUM 55
- Set Voice Mail Number +CSVM 56
- Contact Selector +WCOS 57
- Chapter 9 – Short Messages 60
- Save Settings +CSAS 65
- Restore Settings +CRES 65
- Read Message +CMGR 68
- List Message +CMGL 69
- Send Message +CMGS 70
- Delete Message +CMGD 73
- Message Overwriting +WMGO 76
- Copy Messages +WMCP 78
- Chapter 10 – Supplementary 80
- Services Commands 80
- Call Barring +CLCK 81
- Modify SS Password +CPWD 81
- Call Waiting +CCWA 82
- Advice of Charge +CAOC 85
- List Current Calls +CLCC 88
- Closed User Group +CCUG 91
- Chapter 11 – Data Commands 92
- Select Mode +FCLASS 94
- Select Data Compression %C 97
- Chapter 12 – V.24 and V.25 99
- Set DCD Signal &C 101
- Set DTR Signal &D 102
- Set DSR Signal &S 102
- Back to Online Mode O 102
- Result Code Suppression Q 102
- Default Configuration Z 103
- Save Configuration &W 103
- DCE Response Format V 103
- Auto-Tests &T 104
- Echo E 104
- Multiplexing Mode +WMUX 106
- Chapter 13 – Specific AT 107
- Commands 107
- General Indications +WIND 109
- 0 1 2 3 4 112
- 5 6 7 8 9 112
- 10 11 12 13 14 112
- 15 16 17 18 19 112
- 20 21 22 23 24 112
- Read GPIO Value +WIOR 114
- Write GPIO Value +WIOW 114
- Abort Command +WAC 116
- Play Tone +WTONE 117
- Play DTMF Tone +WDTMF 118
- Downloading +WDWL 118
- Voice Rate +WVR 119
- Data Rate +WDR 120
- Select Voice Gain +WSVG 121
- Status Request +WSTR 121
- Scan +WSCAN 122
- Ring Indicator Mode +WRIM 122
- Custom Character Set +WCCS 124
- Lock +WLCK 125
- CPHS Command +CPHS 126
- CPHS Information +WCPI 129
- Change Default Player +WCDP 130
- CPHS Mail Box Number +WMBN 131
- Reset +WRST 135
- Set Standard Tone +WSST 135
- Hang-up +WATH 136
- Multi-Band Selection +WMBS 137
- Chapter 14 – SIM Toolkit 138
- +STSF=X,XXXXXXXX 139
- SIM Toolkit Commands 140
- Example 141
- Chapter 15 – GPRS commands 149
- +CGQMIN 154
- Enter Data State +CGDATA 157
- Request GPRS IP Service D 162
- Context Activation +CGAUTO 164
- Context Activation +CGANS 165
- Show PDP Address +CGPADDR 166
- Cellular Result Codes +CRC 166
- Example 1 170
- Example 2 170
- Network Request 170
- Chapter 16 – Other AT 171
- Appendix A – Result Codes 172
- Failure Causes, Other Tables 172
- Specific Error Result Codes 174
- Unsolicited Result Codes 179
- Final Result Codes 179
- Intermediate Result Codes 179
- Parameter Storage Mode 180
- GSM Sequences List 182
- Call Barring 183
- Call Waiting 183
- Number Presentation 183
- Operator Names 183
- CPHS Information Field 184
- CSP Constants 185
- Appendix B - ME SIM Toolkit 187
- Support 187
- Terminal Profile 188
- Appendix D – Command Type 190
- Appendix E – Coding of Alpha 191
- Appendix F – Command 193
- Execution and Dependence on 193
- Network Service Commands 194
- Security Commands 194
- Phonebook Commands 194
- Short Messages Commands 194
- Data Commands 195
- V24-V25 Commands 195
- Specific AT Commands 196
- GPRS Commands 197
Relacionado con productos y manuales para Hardware Multi-tech-systems MMCModem GPRS (MTMMC-G)
Hardware Multi-tech-systems CF220 Manual de usuario
(84 paginas)
(84 paginas)
Hardware Multi-tech-systems RF660 Manual de usuario
(189 paginas)
(189 paginas)
Hardware Multi-tech-systems RF102S Manual de usuario
(26 paginas)
(26 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.082 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales