Multi-tech-systems BL-Series Manual de usuario Pagina 162
- Pagina / 168
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
162
MultiModemBL User Guide
International Modem Restrictions
Some dialing and answering defaults and restrictions may vary for international modems. Changing
settings may cause a modem to become non-compliant with national telecom requirements in
specific countries. Also note that some software packages may have features or lack restrictions that
may cause the modem to become non-compliant.
New Zealand Telecom Warning Notice
Use of pulse dialing, when this equipment is connected to the same line as other equipment, may
give rise to ‘bell tinkle’ or noise and may also cause a false answer condition. Should such problems
occur, the user should NOT contact the Telecom Faults Service. The preferred method of dialing is to
use DTMF tones, as this is faster than pulse (decadic) dialing and is readily available on almost all
New Zealand telephone exchanges.
Warning Notice: No ‘111’ or other calls can be made from this device during a mains power failure.
- BL-Series 1
- Intelligent Data/Fax Modem 1
- User Guide 1
- Contents 3
- Chapter 5 - Command Mode 4
- Chapter 6 - S-Registers 4
- Chapter 8 - Modem Testing 5
- 1.1 Introduction 8
- 1.2 How To Use This Manual 8
- 1.3 Modem Features 10
- 1.3.1 2834 Series Features 10
- 1.3.2 1932 Series Features 10
- 1.3.3 1432 Series Features 11
- 1.4 Fax Features 11
- 1.5 Technical Specifications 12
- 1.6 Power 16
- 1.7 Modem LED Indicators 16
- 1.8 Controls on PC Board 17
- MADE IN U.S.A 20
- EIA RS232C 22
- 3.1 Introduction 28
- 3.2 Serial Port Limitations 28
- 3.3 Configuring Your Software 29
- 3.4 PC Initialization Strings 30
- 3.4.2 Other Parameters 30
- 3.5 Macintosh Initialization 31
- 3.6.2 Terminal Emulation 31
- 3.6.3 File Transfer Protocols 32
- 3.8 Modem Basics 33
- 3.8.1 Simple Operations 33
- 4.1 Introduction 36
- 4.2 Dialing/On-Line/Answering 36
- 4.6 Dial-Up Operation 38
- 4.7 Manual Call Origination 38
- 4.8 Automatic Answering 39
- 4.9 Manual Answering 39
- 4.10 Handshaking Details 40
- 4.11 Call Termination 40
- 5.1 Introduction 42
- 5.1.1 AT Command Editing 42
- 5.1.2 Functional Modes 43
- 5.2 Summary of AT Commands 44
- 5.3 Result Codes 47
- 5.4 Dialing Commands 49
- 5.4.1 Dialing Action Commands 49
- 5.4.2 Dial Modifier Commands 50
- 1028806127853500$123456789 52
- Quiet Answer @ 52
- Storing Phone Numbers D...N 53
- Number Linking NN 53
- Modem Reset Z 54
- Unix UUCP Spoofing $SP 55
- Auto Speed Detect #A 60
- Carrier Detect Control &C 61
- CTS Control &R 61
- Data Set Ready Control &S 62
- Normal Mode &E0 63
- Auto-Reliable Mode &E1 63
- Reliable Mode &E2 63
- V.42 Mode Select #L 64
- Auto-Reliable Buffering $A 64
- Retransmit Count $R 65
- 5.4.9 Flow Control Commands 66
- Xon/Xoff Pass-Through &E7 67
- Send Xon/Xoff Characters #X 67
- Maximum Block Size &BS 68
- Parity Selection #P 68
- Through and Pacing Commands 69
- Speed Conversion $BA 70
- Modem Baud Rate $MB 70
- Serial Port Baud Rate $SB 72
- Help Screens $H 73
- Inquiry for Product Code I 73
- Listing S-Register Values L6 73
- Off Hook H 74
- BREAK AT<CR> 74
- Force Answer Mode A 75
- 6.1 Introduction 78
- Remote Configuration 87
- 7.1 Introduction 88
- Configuration 89
- Change LOGIN Password #I 93
- Change SETUP Password #S 93
- Callback Time Delay (S15) 95
- Callback Attempts (S16) 95
- Local Inactivity Timer (S29) 95
- 8.1 Introduction 98
- Digital Analog 99
- Digital Analog DigitalAnalog 100
- 8.5 Back-to-Back Test 102
- 8.6 Synchronous Mode Testing 103
- MultiModemBL User Guide 106
- 9.1 Introduction 108
- 9.3 Speaker Volume Control 114
- DIP-Switches 115
- (-9db/0dB)*/(-15db/-10dB) UP 115
- DIP Switches #13-14 116
- DIP Switches #15-16 116
- 10.1 Introduction 118
- 10.2 Limited Warranty 118
- 10.3 Tech Support 119
- 10.4 Service 119
- 10.5 The Multi-Tech BBS 120
- Appendixes 123
- Appendix A - Troubleshooting 124
- I Am Losing Data 128
- Dial Pulses 130
- Tone Dial Frequencies 130
- Appendix D - Command Summary 131
- Password Command Summary 139
- V.25bis Commands 139
- Asynchronous Mode 140
- Synchronous Mode 141
- Delayed and Forbidden Numbers 147
- V.25bis Operation 147
- V.25bis Mode AT Commands 149
- V.25bis AT Commands 150
- DTR Dialing ($D) Command 151
- 25-PIN DTE 154
- Connector 154
- 25-PIN DCE 154
- Test Voltage - Pin 9, XV 158
- Canadian Limitations Notice 164
- Class A Statement 164
© 2020, manymanuals.es. Todos los derechos reservados | 0.055 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales